Stellarium software png7/22/2023 You should now see the option as described in the “name” tab in the INI file. Go into Stellarium, Press F4 for the View Menu, and go to the landscapes tab. You may have to give permission to create or overwrite the folder. If anything is not correct it’s better to edit there and drag the whole folder again, keeping yourself a backup. Keep the copy of the folder on your desktop. It doesn’t matter what you call your folder, the name showing in Stellarium will come from your. This will normally be C:\Program Files\Stellarium\landscapes. The folder on your desktop needs copying to your Stellarium/landscapes folder. The latitude and longitude of Ron’s house is approximately 53 deg 3 mins North, 0 deg 48 mins West The convention on longitude is that minus is West. Name = Ron, Lynn and Daisy's House in NewarkĪ)Change the name to the name of your siteī)Change the description to describe your observatoryĬ)Change the latitude and longitude to describe your position. In there put your PNG file, named as landscape.pngĪlso in that folder, with a text editor, create the file “landscape.ini” and paste the following (blue here) lines into it. I create a folder on my desktop, this time called “RonsHouse”, but whatever you like. The area above the sky can be added as transparent area, the area below I have filled with green, so can be extended or cut as necessary. I reduced to the correct width, and then played around adding and subtracting to the height to get the exact size. You don’t want your software to distort the image during the reduction. Reducing to the correct size can take a bit of doing. Keep a copy at the original size just in case! Having used the extra resolution to get a nice clean ‘cut out’, use your editing software to make get the image the correct size. Here’s my landscape, with the transparent background shown as a checkerboard pattern. Use your software and an eraser tool, or a brush tool, and eat away the sky carefully, leaving a clean as possible break between the sky and the background. This is good though, because the extra resolution makes it easier to carefully remove the sky. The resolution of modern cameras means that at this stage the file will be quite large, much larger than when it will be used later, in Stellarium. So use your imaging software to save as a. The first thing to be aware of is that the file needs to be capable of having a transparent background. I found it useful to look for the same object at each side to help with the crop. However many photographs you need for the 360, stitch your photos together, I used Photoshop, but you could use Microsoft ICE, or whichever software you are familiar with.Īfter stitching you should carefully crop the photo at the edges so that you have exactly a 360 degree view. I took two panoramas, each of slightly greater than 180 degrees. This can be done as a series of shots with an SLR, but I found that the easiest method was to use a mobile phone set to panorama mode. You need to capture a 360 degree landscape, taken from your observing site. These two steps will make getting your landscape working much easier. Press F2 to get to the configuration menu, then on the “Main” tab, press “Save Settings”. Having changed those two settings, make sure they are saved. Look carefully below, you can just see my background, it would otherwise be totally black in this night view. When it is ticked you see a light rendition of your background, so you can see what you see things relative to the background. If this is left unticked, when the sky goes dark, so does the background, and you can’t orientate yourself. It’s the Minimal Brightness check box, which I like to have ticked. The other setting I like to change is on the View Menu, landscape tab. I like to untick this showing the sky as dark during the day. “Atmospheric Visualisation” is normally ticked, note the sky normally shows daylight. doesn’t go dark when time gets to night time). you can see the stars during daylight hours), and the background is always visible (i.e. This is personal choice, but I find that the most useful view of Stellarium is when the daylight visualisation is off (i.e. It’s fairly straightforward, so I’d like to share the process. I’ve recently created a custom landscape and it’s been really helpful, allowing me to see the stars and planets like they would from my observatory (i.e.
0 Comments
Leave a Reply. |